ZE3198 PLC Trainer Kit with simulators Electrical Training Equipment Educational Equipment For College, University
1 Product overview
1.1 Profile
This training device including Siemens S7-200 PLC and training simulation modules such as control object, through the relevant experiment, students can be familiar with the basic use of Siemens PLC and programming method and the use of programming software. Trains the student to the corresponding knowledge and skills,it is suitable for university, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination. 1.2 Feature
(1) Trainer using aluminum column frame structure, measuring instrument and practical power built-in integration installation, practical circuit and device adopts hanging box combinations, each unit with flexible, easy to use, not easy to damage.
(2) Experimental circuit and device configuration is complete, can be combined, to complete a variety of subjects of training content.
(3) Trainer has a good safety protection system. Allows operation, students independent experiment to cultivate students' ability to analyze and solve problems. 1.3 Technical parameter
(1) Input power: 230 v + 10% for 50 hz, single-phase three-wire system
(2) Dimension: 1200mm×300mm×780mm
(3)Capacity: < 2 kva
(4)Weight : < 100 kg
(5) working conditions: temperature - 10 ℃ ~ + 40 ℃ relative humidity < 85% (25 ℃) 1.4 Equipment composition
1 Power control box
Power control box takes aluminum structure, box type close structure, connect with training frame. 2 Configuration for power control box
(1), Single-phase three-wire power input ,the residual current circuit breaker control, a stop control button, an emergency stop button circuit breaker to cut off the power supply.
(2) the voltmeter and ammeter do output instructions, equipped with 0 to 10 v and 4-20 ma signal generator.
(3) the configuration power light, European-style power input plug and secure power supply output terminals.
(4) built-in ac power supply, with short circuit protection function. 3 Hanging box module
This module can satisfy students do a variety of different experiment, each test module is made, according to a standard size when installing the first module in the aluminum casting of beam in top insert card slot, and then aim the module bottom tank under push down, the module card on the beam. Hanging box module as shown. 5 Equip components
(1) Siemens S7-200 PLC module and I/O modules hanging box 1 piece
(2) Temperature control box 1 piece
(3) Elevator hanging box 1 piece
(4) Traffic lights hanging box 1 piece
(5) Mechanical and electrical load hanging box 1 piece
(6) Some 2mm safety electrical cable
(7) 4mm safety electrical cable 3 cables 1.5 Warning and Notice
1. Experiment training set inlet wire should connect correct, and ensure connect to ground connection is good.
2. When use it, your hands should keep dry, clean. Don’t use sharp tools to touch equipment surface.
3. When do experiment, connect circuit correct, you should ask teacher, after teacher’s confirm, you can connect power supply. It is forbid use hand or electric conduction touch electrical part. If you unprofessional operation , you should be responsible for your action.
4. After experiment, you should cut off main power supply, make breaker handle to down direction.
5. When motor working, forbid hand touch motor rotate axis, so as to avoid hurt. When power on, forbid to exceed components rated voltage, work power.
6.For the experiments measuring instrument , when use, mustn’t exceed the range. If breaker automatic release, you should press reset button, and then can power on again, if not, the breaker can’t work normally, forbid forced power transmission.
7. When met emergency condition, you should turn off power breaker immediately. When remove fault, you should power on breaker again, various axis will go back to original position, and then do positioning and assembly experiment. 1.6 Experiment that can be finished
(1) Temperature control simulation training
(2) Traffic lights experiment simulation training
(3) Elevator control practice
(4) Mechanical and electrical load simulation training
(5) Siemens S7-200 PLC programming practice
For similar product, please see ZE3108
